The radio control link connects your transmitter to your drone. If it fails, you lose control, so it is one of the most important choices in any build. Today most FPV and long-range pilots use digital links such as ExpressLRS (ELRS) and TBS Crossfire, while many ready-made radios still ship with older 2.4 GHz protocols. In this guide we explain how RC links work, compare the popular options and help you choose the right RC link for your drone.
What an RC link does
Your transmitter reads the stick and switch positions and sends them many times per second to a receiver on the drone. The receiver passes them to the flight controller, usually over a serial connection. Modern links also send telemetry back to the transmitter: battery voltage, signal strength and sometimes GPS position.
Three numbers describe how good a link is:
- Range: how far you can fly before the signal becomes unreliable.
- Latency and packet rate: how quickly and how often your commands arrive. Higher packet rates feel more connected for fast flying.
- Robustness: how well the link survives interference and obstacles.
Frequency bands: 2.4 GHz vs 868/915 MHz
- 2.4 GHz: small antennas, high packet rates and worldwide availability. Range is good for most flying.
- Sub-GHz (868 MHz in Europe and some other regions, 915 MHz in the Americas and others): lower frequencies pass through obstacles and travel further, so they are popular for long range. Antennas are larger.
Which frequencies and power levels are allowed depends on your country. Always set your equipment to the correct regional settings and follow local radio regulations.
ExpressLRS (ELRS)
ExpressLRS is an open-source RC link that has become very popular because it offers excellent performance at low cost.
- Available on 2.4 GHz and sub-GHz bands.
- Very high packet rates for racing and freestyle, and long-range modes for distance flying.
- Small, light and inexpensive receivers, made by many manufacturers.
- Supported by Betaflight, INAV and ArduPilot using the CRSF serial protocol.
- Configured through a web interface or a Lua script on the transmitter. Transmitter and receiver must use compatible firmware versions and the same binding phrase.
TBS Crossfire and Tracer
TBS Crossfire is a proven long-range sub-GHz system that made the CRSF protocol popular. TBS Tracer is its 2.4 GHz counterpart.
- Well known for reliable long-range performance.
- Mature ecosystem with good telemetry support.
- Generally more expensive than ELRS, with fewer receiver makers.
Other common protocols
- FrSky (ACCST/ACCESS): long-standing 2.4 GHz systems used on many radios.
- FlySky, Spektrum and others: often found in ready-to-fly kits and RC planes.
- SBUS and PPM: these are connection protocols between the receiver and flight controller, not radio links.
RC link comparison
| Feature | ELRS 2.4 GHz | ELRS sub-GHz | Crossfire | Older 2.4 GHz |
|---|---|---|---|---|
| Range | Very good | Excellent | Excellent | Good |
| Packet rate / latency | Very high / low | Medium | Medium | Medium |
| Receiver size | Very small | Small, bigger antenna | Small, bigger antenna | Varies |
| Cost | Low | Low | Higher | Varies |
| Open source | Yes | Yes | No | No |
| Best for | Freestyle, racing, general | Long range | Long range | Existing setups |
How to choose
- New FPV pilot: ELRS 2.4 GHz gives excellent performance for the price.
- Long-range FPV or fixed-wing: ELRS sub-GHz or Crossfire.
- Racing: ELRS 2.4 GHz at a high packet rate.
- ArduPilot missions with a ground station: pair your RC link with a telemetry radio, or use a link that supports MAVLink telemetry.
Installation and safety tips
- Mount receiver antennas away from carbon fiber and metal, which block radio signals. Point them in different directions if the receiver has two.
- Keep the receiver antenna away from the video transmitter to reduce interference.
- Set up failsafe in your flight controller and test it with props removed by switching off the transmitter.
- Do a range check before long flights, and watch the link quality (LQ) value in your OSD.
- Keep firmware matched between transmitter and receiver after updates.
The radio link and the video link work together; see analog vs digital FPV. Setting up failsafes in ArduPilot is covered in our ArduPilot setup guide.
Frequently asked questions
Is ELRS better than Crossfire?
ELRS offers similar or better performance for most pilots at a lower cost and with more receiver choices. Crossfire remains a reliable, proven long-range system.
Which is better for long range, 2.4 GHz or 900 MHz?
Sub-GHz bands generally travel further and handle obstacles better, so they are popular for long range. Modern 2.4 GHz links also reach impressive distances in open areas.
What is CRSF?
CRSF is a serial protocol used between the receiver and flight controller by both Crossfire and ExpressLRS. It carries control channels and telemetry.
Why does my receiver not bind?
Common causes are mismatched firmware versions, different binding phrases on ELRS, or a wrong regional frequency setting.