The GPS module is one of the most important parts of any drone that holds position, returns home or flies missions on its own. For years the u-blox M8N was the default choice. Today most new drone GPS modules use the newer u-blox M10 chip. So is the M10 vs M8N upgrade worth it? In this comparison we look at satellite systems, accuracy, update rate, power use and real flying, so you can choose the right drone GPS module for your build.
Quick answer
For a new build, choose an M10-based GPS module. It tracks four satellite systems at once, gets a position fix as fast or faster, uses much less power and usually costs about the same as a good M8N. Keep an existing M8N if it works well: the difference in normal flying is real but not dramatic.
What M8N and M10 actually are
M8N and M10 are GNSS (Global Navigation Satellite System) receiver chips made by the Swiss company u-blox. Drone GPS modules from many brands put one of these chips on a small board together with a ceramic patch antenna, often a compass chip, and sometimes an LED or a safety switch.
The “M8” and “M10” names are chip generations. M8 was released in the mid-2010s; M10 is a newer, more power-efficient generation. Both receive the same main civil signal band (L1/E1/B1), so neither is a dual-band or centimeter-level RTK receiver.
M10 vs M8N: specification comparison
The figures below are typical values from u-blox datasheets for the receiver chips. Real modules vary with antenna size, board design and how they are mounted on your drone.
| Feature | u-blox M8N | u-blox M10 |
|---|---|---|
| Satellite systems tracked at the same time | Up to 3 | Up to 4 (GPS, Galileo, GLONASS, BeiDou) |
| Frequency band | Single band (L1) | Single band (L1) |
| Horizontal accuracy (open sky) | About 2.5 m CEP | About 1.5 m CEP |
| Navigation update rate | Up to 10 Hz | Up to 10 Hz with all systems |
| Cold start (typical) | About 26 s | About 23–30 s |
| Power use while tracking | Moderate | Very low, a fraction of M8N |
| Typical module price | Low to medium | Low to medium |
CEP (circular error probable) means that half of the position readings fall inside a circle of that radius. It is a common way to describe GPS accuracy.
The big difference: four satellite systems at once
The most useful upgrade in the M10 is that it can track GPS, Galileo, GLONASS and BeiDou together. The M8N can use up to three systems at the same time.
Why does this matter for drones? More satellite systems means more satellites in view. With more satellites, the receiver can pick the best-placed ones, keep a stronger solution when some are blocked by buildings or trees, and recover faster after a sharp turn or a moment of interference. For a drone that has to hold position or fly home, a higher and steadier satellite count is exactly what you want.
In open fields both chips usually see plenty of satellites. The advantage of the M10 shows most near buildings, hills and tree lines, and at the start of a flight when you are waiting for a fix.
Accuracy in real flying
On paper the M10 is more accurate (about 1.5 m CEP against about 2.5 m). In practice, three things affect your drone’s position hold more than the chip itself:
- Antenna size and quality. A larger ceramic antenna (for example 25 × 25 mm) usually beats a tiny one, whatever the chip.
- Interference. Video transmitters, cameras, ESCs and USB 3 devices can produce noise that weakens GPS reception. Mount the GPS on top, away from these parts, ideally on a short mast.
- Compass setup. Many “GPS problems” such as toilet-bowling or drifting circles are really compass problems caused by power wires or metal near the compass chip.
For centimeter-level accuracy, neither chip is enough on its own. Survey and mapping drones use dual-band RTK receivers such as the u-blox F9P with a correction source.
Power use and why it matters
The M10 was designed for very low power use. On a large drone the saving is small compared with the motors, but it helps in small builds, on 5 V rails that are already loaded, and in GPS units that run from the flight controller’s USB power on the bench. Lower power also means slightly less heat inside small enclosures.
Compatibility with ArduPilot, PX4, INAV and Betaflight
Both chips speak the u-blox protocol, and both are supported by the common open-source flight stacks: ArduPilot, PX4, INAV and Betaflight. In most cases you connect the module to a free UART on the flight controller (GPS TX to FC RX, GPS RX to FC TX, plus 5 V and ground) and the firmware detects and configures it automatically.
If the module has a compass, its two extra wires (SDA and SCL) go to the I2C port. Check your firmware’s documentation for the right serial port setting and baud rate options, and update to a recent firmware version so the M10 is fully supported.
Watch out for fake M8N modules
Because the M8N has been popular for a long time, many low-cost modules sold as “M8N” use older or cloned chips. They may track fewer satellites, take a long time to get a fix, or fail to save settings. Buy from reputable brands and shops, and check the chip version shown in your ground station or u-blox u-center software after connecting the module.
Which one should you buy?
- Building a new drone: choose an M10 module with a reasonably large antenna and a good compass.
- Small FPV quad (GPS rescue only): a compact M10 module is ideal thanks to its low power use and fast fix.
- Existing drone with a good M8N: keep it unless you fly near buildings or trees and see weak satellite counts.
- Mapping or survey work: look beyond both, to dual-band RTK receivers.
Installation tips for a strong GPS signal
- Mount the GPS on the highest point of the drone, antenna facing the sky.
- Keep it at least a few centimeters away from the video transmitter, camera, ESCs and power wires. A short GPS mast helps a lot.
- Point the module’s arrow forward, or set its orientation correctly in your firmware.
- Calibrate the compass outdoors, away from cars and metal structures.
- Before each flight, wait for a solid 3D fix with a good satellite count before arming in GPS modes.
Frequently asked questions
Is M10 better than M8N for drones?
Yes, for new builds. The M10 tracks four satellite systems at once, is slightly more accurate on paper and uses far less power, at a similar price.
Can I replace an M8N with an M10 without changing settings?
Usually yes. Both use the u-blox protocol and most flight controller firmware detects them automatically. Update your firmware first and check the GPS serial port settings.
Does the M10 give centimeter accuracy?
No. Like the M8N, the M10 is a single-band receiver with meter-level accuracy. Centimeter accuracy needs a dual-band RTK system with corrections.
Why does my GPS take so long to get a fix?
Common causes are interference from the video transmitter or camera, a poor antenna, a fake chip, or flying from a spot with a blocked sky view. A cold start after the module has been off for a long time also takes longer.
Do I need a GPS module with a compass?
For ArduPilot, PX4 and INAV position modes on multirotors, a compass is strongly recommended. For simple GPS rescue on small FPV quads, some setups work without one.
Building a drone from scratch? Read our guide Motor KV Explained: How to Choose the Right Brushless Motor for Your Drone to match your motors, propellers and battery.