News · Drone Rules Around the World: How Different Countries Regulate DronesNews · Solar-Powered HAPS: The Drones That Want to Replace SatellitesNews · What Are MALE and HALE Drones? Long-Endurance UAVs ExplainedNews · UAV Classes Explained: From Micro Drones to HALEGuides · Drone Battery Care: Charging, Storage and Lifespan
Guides · Intermediate

Quadplane vs Tailsitter: How VTOL Drones Work

How VTOL drones take off like a multirotor and fly like a plane, quadplane vs tailsitter compared, and tips for setting up a VTOL with ArduPilot.

By Mirza Khurram Shahzad · October 11, 2026 · 4 min read

VTOL drones take off and land vertically like a multirotor, then fly efficiently on wings like an airplane. They are becoming the standard choice for professional mapping, inspection and long-distance work because they need no runway and still fly for a long time. There are several VTOL designs, but the two most common are the quadplane and the tailsitter. In this guide we explain how VTOL drones work and compare quadplane vs tailsitter designs in simple terms.

What is a VTOL drone?

VTOL stands for Vertical Take-Off and Landing. A VTOL drone has two flight modes:

  • Hover mode: lift comes from propellers, like a multirotor. Used for take-off, landing and short hovering.
  • Forward flight (fixed-wing) mode: lift comes from the wing, and the drone flies like an airplane. Used for most of the mission because it uses far less energy.

The change between these modes is called the transition. It is the most demanding part of a VTOL flight, and the flight controller manages it automatically.

The quadplane

A quadplane is a normal fixed-wing airplane with four extra vertical lift motors, usually mounted on two booms under the wings. A separate forward motor (pusher or puller) drives the plane in cruise.

  1. The four lift motors raise the aircraft vertically.
  2. The forward motor accelerates the plane until the wing produces enough lift.
  3. The lift motors slow down and stop. The aircraft flies as a normal plane.
  4. For landing, the lift motors start again, the plane slows down and descends vertically.

Advantages: simple and robust transition, easy to tune, works with ordinary airplane designs, and the fuselage stays horizontal so cameras point straight down.

Disadvantages: the lift motors, booms and their batteries are extra weight and drag in cruise, which reduces efficiency.

The tailsitter

A tailsitter takes off sitting on its tail, pointing straight up. Its propellers act as rotors for vertical flight, then the whole aircraft tilts forward 90 degrees to fly on its wing.

Advantages: no extra lift motors, so there is less weight and drag in cruise. The design can be very simple mechanically.

Disadvantages: the big wing acts like a sail while hovering, so tailsitters are sensitive to wind during take-off and landing. The transition is more demanding to tune, and cameras need careful mounting because the body rotates through 90 degrees.

Other VTOL designs

  • Tiltrotor: the motors tilt from vertical to horizontal. Efficient, but mechanically more complex.
  • Tiltwing: the whole wing tilts with the motors. Rare in small drones because of its complexity.

Quadplane vs tailsitter comparison

Feature Quadplane Tailsitter
Extra lift motors Yes (usually four) No
Cruise efficiency Good Very good
Wind handling in hover Good More difficult
Transition Smooth and forgiving More demanding
Tuning difficulty Easier Harder
Payload and camera mounting Easy (body stays level) More complex
Best for Mapping, inspection, beginners to VTOL Experienced builders, maximum efficiency

How to choose

  • Your first VTOL: choose a quadplane. It is more forgiving to set up and fly.
  • Mapping and survey work: a quadplane keeps the camera level and handles typical field winds well.
  • Maximum efficiency and light weight: a well-designed tailsitter can fly longer on the same battery, if you can handle the tuning.

Setting up a VTOL with ArduPilot

ArduPilot’s Plane firmware supports quadplanes, tailsitters and tiltrotors. A typical setup process is:

  1. Build and set up the aircraft as a normal plane first, and check control surfaces move correctly.
  2. Enable VTOL support and choose the frame type for the lift motors.
  3. Test the lift motors with propellers removed, checking order and direction.
  4. Test hover in a VTOL hover mode at low height, in calm wind.
  5. Test transitions carefully at a safe height, with a plan to switch back to hover if needed.
  6. Tune hover and forward-flight controllers using logs.

New to ArduPilot? Start with our ArduPilot setup guide, and choose a capable flight controller: see H7 vs F7.

Power system tips for VTOL drones

  • Lift motors must handle hover alone, with margin for wind, because the wing gives no lift at low speed.
  • Size the battery for hover current peaks, which are much higher than cruise current. This is why many VTOLs use LiPo or high-current Li-ion packs. See Li-ion vs LiPo.
  • Use efficient props for cruise, and consider folding or stopping lift props to reduce drag.

Frequently asked questions

What is the difference between a quadplane and a tailsitter?

A quadplane adds separate lift motors to a normal airplane and stays level during take-off. A tailsitter takes off pointing straight up and tilts 90 degrees to fly on its wing, without extra lift motors.

Are VTOL drones hard to fly?

With modern autopilots, take-off, transition and landing are automated. The hard part is the initial setup and tuning, which must be done carefully.

How long can a VTOL drone fly?

Many mapping VTOLs fly for 60 to 120 minutes or more, because they spend most of the flight on their wings.

Which is better for mapping, VTOL or fixed-wing?

VTOLs need no runway or catapult and can land precisely, which makes field work easier. Conventional fixed-wings are simpler and a little more efficient. See fixed-wing vs quadcopter for mapping.

Mirza Khurram Shahzad

UAV engineer and writer at UAVCodex. Designs, builds and flies fixed-wing, VTOL and multirotor drones.