News · Drone Rules Around the World: How Different Countries Regulate DronesNews · Solar-Powered HAPS: The Drones That Want to Replace SatellitesNews · What Are MALE and HALE Drones? Long-Endurance UAVs ExplainedNews · UAV Classes Explained: From Micro Drones to HALEGuides · Drone Battery Care: Charging, Storage and Lifespan
Components

H7 vs F7 Flight Controllers: What’s the Real Difference?

H7 vs F7 flight controllers compared: clock speed, flash memory, firmware support and which one to buy for FPV, long-range, fixed-wing and ArduPilot builds.

By Mirza Khurram Shahzad · October 10, 2026 · 5 min read · Updated October 11, 2026
Codex entry CX-9008Components
Chip
STM32H743
Clock
480 MHz
Flash
2 MB
RAM
~1 MB

The flight controller is the brain of your drone. When you shop for one today, most boards are built around one of two processor families: STM32 F7 or STM32 H7. Prices differ, the spec sheets look similar, and forum advice often contradicts itself. In this guide we compare H7 vs F7 flight controllers in plain language: what the chips really are, where the extra power of the H7 matters, and which one you should buy for FPV, long-range, fixed-wing or autonomous builds.

Quick answer

For a Betaflight freestyle or racing quad, a good F7 board is still more than enough. For ArduPilot, PX4 or INAV builds such as fixed-wings, VTOLs, long-range and mapping drones, choose an H7 board: it has more processing power, much more memory and more room for future firmware features.

What “F7” and “H7” mean

F7 and H7 are families of microcontrollers made by STMicroelectronics. Flight controller makers put one of these chips on a board together with the gyro and accelerometer (IMU), a barometer, voltage regulators, connectors and sometimes an on-screen-display (OSD) chip.

Both families use an ARM Cortex-M7 core, so they share the same basic design. The difference is in speed, memory and features:

  • Common F7 chips: STM32F722, STM32F745 and STM32F765.
  • Common H7 chips: STM32H743, STM32H750 and the newer STM32H723/H725 family.

H7 vs F7: specification comparison

The table shows typical values for the chips most often used on drone flight controllers. Individual boards add their own sensors and ports.

Feature F722 F745 / F765 H743
CPU core Cortex-M7 Cortex-M7 Cortex-M7
Maximum clock speed 216 MHz 216 MHz 480 MHz
Flash memory 512 KB 1 MB / 2 MB 2 MB
RAM 256 KB 320 KB / 512 KB About 1 MB
Typical firmware Betaflight, INAV Betaflight, INAV, ArduPilot All major firmware
Typical board price Low Medium Medium to high

Where the H7’s extra power actually matters

1. Firmware with lots of features

Betaflight is focused on fast, precise flight and runs comfortably on F7 chips. ArduPilot and PX4 do much more: an extended Kalman filter (EKF) that blends GPS, compass, barometer and IMU data, autonomous missions, geofences, scripting, advanced logging and support for many sensors at once. All of this needs processing time and memory. An H7 gives that firmware plenty of headroom, and ArduPilot developers increasingly target H7 boards for new features.

2. Flash memory: the hidden limit

Flash memory is where the firmware itself is stored. Many F722 boards have only 512 KB of flash, which is enough for Betaflight and INAV but limits them for larger firmware. ArduPilot generally needs boards with at least 1 MB of flash, and boards near that limit get reduced feature sets. With 2 MB, H743 boards avoid this problem for the foreseeable future.

3. More filtering and higher loop rates

Modern flight software runs many filters on the gyro signal to remove motor noise. More filters and higher loop rates need more CPU time. Both chip families handle typical Betaflight settings, but the H7 leaves more margin when you enable advanced features such as extra filters, high logging rates or bidirectional DShot on many motors.

4. Logging and peripherals

H7 boards often add an SD card slot for long logs, more serial ports, a CAN bus for DroneCAN GPS and sensors, and dual IMUs for redundancy. These are board features rather than chip features, but they are much more common on H7 designs aimed at ArduPilot and PX4.

When an F7 board is the better choice

  • 5-inch freestyle and racing quads on Betaflight. An F7 runs Betaflight with plenty of headroom, and the money you save can go to better motors or a better camera.
  • Small and light builds. Many compact all-in-one and 20×20 mm boards use F7 chips.
  • Simple INAV builds such as a basic fixed-wing with GPS return-to-home, as long as the board has enough serial ports.

When you should choose an H7

  • ArduPilot or PX4 builds: fixed-wings, VTOLs, multirotors for mapping or inspection, and any autonomous mission work.
  • Long-range drones that use GPS, a compass, telemetry radios and several serial devices at once.
  • Builds you want to keep for years. Firmware grows over time; the extra flash and RAM keep an H7 board useful longer.

Things that matter more than the chip

Two boards with the same processor can perform very differently. Before buying, check these points:

  1. IMU quality and mounting. A clean gyro signal matters more than CPU speed. Soft mounting and a well-designed board reduce vibration problems.
  2. Number of UARTs. Count your devices: receiver, GPS, VTX control, telemetry, ESC telemetry. Make sure the board has enough free serial ports.
  3. Power regulators (BECs). Check the 5 V and 9–12 V outputs can supply your camera, VTX, GPS and servos with margin.
  4. Firmware support. Confirm the exact board name is listed by the firmware you plan to use before you buy.
  5. Connectors and size. Mounting pattern (20×20, 30.5×30.5 mm), plug-in cables versus solder pads, and a solid ground layout save hours of building time.

What about F4 boards?

F405 boards are still widely used and cheap. They are fine for many Betaflight builds, but they have less flash and processing power than F7 and H7 chips. For a new build that may run ArduPilot or INAV with GPS, an F4 is the least future-proof choice.

Our recommendation

  • Betaflight 5-inch freestyle or racing: F7 (or H7 if the price difference is small).
  • INAV fixed-wing or long range: H7 preferred, F7 with enough UARTs acceptable.
  • ArduPilot or PX4, VTOL, mapping or autonomous missions: H7.

Pair your flight controller with a good GPS: see our comparison M10 vs M8N GPS module. And to choose the motors it will drive, read Motor KV Explained.

Frequently asked questions

Is H7 better than F7 for Betaflight?

An H7 has more headroom, but for typical Betaflight settings a quality F7 board flies just as well. The difference you feel in the air usually comes from tuning, filtering and vibration, not the processor.

Can I run ArduPilot on an F7 flight controller?

Yes, on supported F7 boards with enough flash memory, usually 1 MB or more. Boards with 512 KB of flash are mainly used with Betaflight and INAV.

Does an H7 flight controller use more power?

Slightly, but the difference is tiny compared with motors, the video system and the receiver. It does not noticeably affect flight time.

Is an H7 board worth the extra cost for a beginner?

If you plan to learn ArduPilot, INAV or autonomous flight, yes. If you only want to fly freestyle on Betaflight, an F7 board is a sensible way to save money.

Mirza Khurram Shahzad

UAV engineer and writer at UAVCodex. Designs, builds and flies fixed-wing, VTOL and multirotor drones.